Skip to content

D&G Window Solutions · Fenestration Knowledge Series

Condensation, Draughts and Thermal Performance in Steel Windows

How glass, seals, drainage, repair and secondary glazing work together to improve comfort in steel windows.

Article 084 November 2026By D&G Window Solutions

Article 08 · D&G Window Solutions Fenestration Knowledge Series

Condensation on a steel window is easy to notice. The harder question is what it means.

It may indicate warm, moist indoor air meeting a cold pane. It may point to a failed seal, blocked drainage path or a sash that no longer closes squarely. In some buildings it is also a symptom of poor ventilation, an unheated room or a change in how the space is used.

The answer is rarely “replace the glass” in isolation. A steel window is a complete opening: frame, glass, putty or bead, hardware, seals, drainage, installation and the wall around it. Thermal comfort improves when those parts are assessed together.

What condensation is telling you

Indoor air contains water vapour. When that air touches a surface below its dew point, the vapour becomes liquid water. The colder the inside surface, and the more moisture in the room, the greater the chance of condensation.

On a steel window, the first places to check are:

  • the lower edge of the glass and the frame;
  • corners, glazing bars and areas beside cold metal sections;
  • failed putty, open joints or cracked sealant;
  • a sash that does not close evenly; and
  • concealed drainage paths that are blocked with paint, dirt or debris.

Condensation on the room side is different from water between panes or water on the external face. Each pattern suggests a different investigation. Wiping the glass is temporary maintenance, not a diagnosis.

Draughts are usually air-path problems

A draught is uncontrolled air movement through a gap. On an older steel or metal window, the gap may come from worn hinges, distortion, missing putty, a perished seal, a loose meeting rail or a frame that has shifted slightly in the opening.

Before adding a thicker pane, identify the air path. Check the perimeter between frame and wall, the meeting stiles, opening lights, hardware and the junction between glass and frame. A window can have excellent glass and still feel cold if air is bypassing the sash.

The repair approach should match the condition. D&G Window Solutions’ steel and metal refurbishment service can address corrosion, stiff hardware, failed putty and mechanical operation before a glazing upgrade is specified.

Thermal performance has more than one measure

“Thermal performance” can mean several things:

  • Surface temperature: how warm the inside face of the glass and frame feels;
  • Air leakage: how much unplanned air moves through gaps;
  • Heat transfer: how readily heat passes through the glass and frame; and
  • Solar gain: how much sunlight warms the room through the opening.

A low-emissivity coating may reduce heat transfer through the glass, but it will not repair a leaking perimeter. A new seal may reduce draughts while leaving a very cold single pane. A shading strategy may be more useful on a sun-exposed elevation than a darker glass specification.

The correct intervention depends on which problem the occupants are actually experiencing.

Start with the frame and the building

On an existing opening, inspect the steel before selecting a glass build-up. Look for section loss, corrosion at sills and corners, loose glazing bars, failed putty, distorted sashes and signs of water entry. Confirm the rebate depth, edge cover, drainage and hardware capacity.

The room matters too. Kitchens, bathrooms and bedrooms can create very different moisture loads. Furniture, curtains and blinds can restrict air movement at the glass. Extract ventilation, heating patterns and changes to occupancy can alter condensation even when the window has not changed.

Where the original frame has heritage value, a repair-first assessment helps separate a local maintenance problem from systemic failure. Retaining the frame is often compatible with improving comfort, but the sequence matters: make the opening sound before relying on a new glass specification.

Glass options for comfort

Better single glazing

A carefully selected single pane can still be appropriate where the rebate is shallow, the original appearance is important or the risk and comfort brief is modest. The glass should be chosen with the room, safety requirements and frame condition in mind—not by appearance alone.

Laminated and acoustic glass

Laminated glass can improve safety and, with the right interlayer, acoustic performance. It is heavier than a basic single pane, so hinges, stays and the steel section must carry the finished unit safely. Read How Modern Safety Glass Actually Works for the difference between toughened and laminated breakage behaviour.

Low-E and solar-control coatings

Low-emissivity coatings can make the inner pane feel less cold. Solar-control products can reduce unwanted afternoon heat. Samples should be viewed in the actual elevation because reflectivity, colour and the appearance of a heritage façade all matter.

Double glazing

Double glazing can provide strong thermal performance, but a sealed unit may be too thick or heavy for a slender original steel section. The full unit, spacer, edge cover and glazing method must be checked before it is specified.

Secondary glazing

Where the original outer window should remain, secondary glazing can create a second, carefully detailed air layer inside the room. It may improve comfort and acoustics without replacing the historic frame. It is not automatically right for every room: ventilation, access, sightlines and moisture management still need to be resolved.

Why sealing must be compatible with drainage

Sealing a window is not the same as blocking every opening. Steel windows are designed to shed water through specific paths. Over-sealing a sill, filling a drainage slot or trapping moisture against a corroded section can make the original problem worse.

Use compatible materials and confirm where water is meant to go. On a heritage refurbishment, the glazing detail should be reversible where practical and should not conceal corrosion that still needs treatment.

A practical comfort sequence

For an existing steel or metal window, a sensible sequence is:

  1. Record where condensation, cold air or water entry is occurring.
  2. Check room ventilation, moisture sources, heating and shading.
  3. Inspect the frame, opening lights, hardware, putty, seals and drainage.
  4. Repair corrosion, distortion and mechanical defects before final glass selection.
  5. Compare glass, coating, double-glazing and secondary-glazing options against the rebate, weight and heritage brief.
  6. Detail the glazing and perimeter junction so the opening remains serviceable.
  7. Review performance after installation rather than assuming one material solved every symptom.

For new work, custom steel windows and doors should be designed around the intended glass, hardware and weathering details from the start. Where a new replacement opening is better suited to aluminium, compare custom aluminium windows and doors as part of the same performance discussion.

The right target is a better opening

Condensation and draughts are clues, not product recommendations. The useful question is whether the whole opening is balanced: a sound frame, suitable glass, controlled air paths, open drainage, working hardware and a room that can manage its moisture load.

That approach keeps steel windows primary while treating metal windows, glass and installation as one system. It also protects heritage character by making the smallest effective intervention first.

For a project-specific assessment, contact D&G Window Solutions with the suburb, photographs and approximate opening sizes. We can help distinguish a glazing issue from a repair, ventilation or detailing issue before a quotation is prepared.

Next in the series

Article 09 will examine Repair or Replace? The True Cost of Heritage Windows.